一、概述
ZXD-A轉速信號測控儀可完成水輪機發電機組的轉速百分比或頻率測量，其輸入信號可取主機殘電壓（電流互感器邊）、永磁機電壓，輸出采用七路繼電器控制和一路12位D/A轉換輸出模擬量。機組的轉速百分比和頻率由四位LED數碼管顯示，七路繼電器的工作狀態由七只LED發光二極管分別指示。本儀表除可帶4—20mA ,1—5V ，0—20mA， 0—5V等標準直流信號輸出外，還可帶RS—485，RS—232C，RS—422A等標準串行口輸出，輸出采用光電隔離，使得儀表可以與計算機直接接口。
本儀表關鍵元器件采用美國ATMEL公司、 MAXIM公司、TI公司的產品。儀表掉電采用E2PROM數據保護，初始設置的所有參數及工作狀態不會因突然停電而丟失，可永久保存；輸入、輸出采用光電隔離技術，使得儀表完全滿足電廠安全、及時、穩定、可靠的工作要求。
二、主要技術參數
1、輸入信號
1）發電機殘壓；2）發電機PT頻率
2、輸入電壓范圍：發電機殘壓或PT信號0.3-250VAC
3、測量精度： 0.1級
4、測頻范圍：頻率0.02 –99.99 HZ、 轉速百分比 2%-200%
5、輸出信號
1）7路繼電器常開觸點輸出
2）模擬信號輸出： 4—20mA (對應于機組轉速的0%-200%)
3) RS485串行通信接口輸出：標準MODBUS通信協議
6、工作環境： 溫度-10—50 ℃ ，相對濕度≤85% 無腐蝕性氣體及導電、易爆、塵埃等場所。
7、外型尺寸 ： 寬×高×深 = 160 ×80×160 mm
8、電源 ：開關電源，交流185——250V或直流75——300V
E． Outline
ZXDThe rotational speed signal observation meter may complete hydraulic turbine power set the rotational speed percentage or the frequency measurement, its input signal may take the main engine remnant voltage (nearby current transformer), permanent magnetism machine voltage, the output uses seven group black-white controls and a group 12 D/A transformation output simulation quantity. Unit's rotational speed percentage and the frequency demonstrated by four LED nixietubes that seven group relay's active statuses instructed separately by seven LED light emitter diode. This measuring appliance besides may bring 4-20mA, 1-5V, 0-20mA, standard cocurrent signal outputs and so on 0-5V, but may also bring RS-485, RS-232C, RS-422A and so on standard serial port output, the output uses the electro-optical isolation, causes the measuring appliance to be possible with the computer direct connection
This measuring appliance essential primary device uses American ATMEL Corporation, MAXIM Corporation, the TI Corporation's product. The measuring appliance power failure uses the E2PROM data protection, because initial establishment's all parameters and the active status will not cut power suddenly lose, but permanent preservation; The input, the output use the electro-optical isolation technology, causes the measuring appliance to satisfy the power plant safely completely, prompt, stable, the reliable work requirement
二、Major technique parameter
1、Input signal :
1）Generator remnant pressure ；2）Generator PT frequency
2、Input voltage scope ：Generator remnant pressure or PT signal 0.3-250VAC
3、Measuring accuracy:0.1 level
4、Frequency measurement scope: Frequency 0.02 - 99.99 HZ, rotational speed percentage 2%-200%
5、output signal
1) 7 group relay normally opened contact output
2) simulated signal output: 4-20mA (corresponds to unit rotational speed 0%-200%)
3) RS485 serial communication connection output: Standard MODBUS communication protocol
6、Working conditions: Temperature - 10-50 ℃, relative humidity ≤85% non-corrosiveness gas and electric conduction, explosive, places and so on dust.
7、Outlook size: Wide * high * deep = 160 ×80×160 mm
8、Power source: The switching power supply, exchanges 185--250V or directs current 75--300V
關注我們的微信